Photo (interior) of a reconstructed carinate globular pottery jar, with profile depicted (left). The jar was partially exposed, sitting upright in the east profile wall of the unit. The jar broke insitu and half of the vessel was removed and reconstructed. The jar has a narrow mouth. The interior surface of the jar is heavily eroded, perhaps an indication that the jar was used to store a fermented liquid like millet or sorghum beer. A jar of similar form, decoration and interior wear was found one meter away and at a slightly higher level in the same unit (KK 95-350). Rim diameter: 10 cm. 50% of vessel reconstructed. Photo scale in cm. Kuulo Kataa. 10 July, 1995.
Photo of an inward-curving (recurved) jar rim sherd, with profile depicted (left). A zone of diagonally oriented dentate (comb) impressions is bounded on upper and lower edges by a shallow horizontal groove. A mica paint/slip was applied over top of the dentate impressions. The ceramic fabric was tempered with angular quartz grit. An INAA sample ("KK NA-29") was unassigned to a specific group of ceramic fabrics, lending no insight into where the jar was made. Interior neck diameter: 18 cm. Sherd represents an 12% of the jar's circumference. Scale in cm. Kuulo Kataa. 25 June, 1995.
Side view of a broken pottery sherd with a large slag inclusion. The use of crushed slag as a tempering material included in potting clay is first seen in pottery associated with Ngre phase sites in the Banda area. The use of crushed slag as a temper intensifies during Kuulo phase times, after which it becomes uncommon. Ngre Kataa, June, 2008.
Photo of an everted-rim jar excavated from Ngre Kataa, Mound 1, Unit 1, levels 3-6. The jar (Vessel 1) was found upside-down, resting on its rim and in association with a cluster of several other complete (Vessels 2 & 3) and broken pots in what has been interpreted as a kitchen area. The round-based jar is decorated on its lower surface by faint twisted cord-roulette impressions. The zone of cord rouletting is separated from the undecorated surface above by three arching grooves or channels. Multiple small circular punctates mark the place where grooved lines meet. Whole pot. Rim diameter c. 30 cm at exterior lip. Photo scale in cm. Site Ngre Kataa ("Banda 40"). 5 April, 2001.
Photo of a large pottery bowl. The rim is angled inward, creating a carination where the bowl's rim and body meet. Above the carination and around the rim's circumference, the exterior surface is decorated with shallow parallel grooves. The bowl's upper body is decorated with several clusters of triangular impressions which are bounded by angled pairs of grooved lines. The interior and exterior surfaces of the bowl are burnished, giving the bowl a slight sheen. A small pedestal stabilizes the bowl at its base. The bowl is consistent in shape and size with serving/eating bowls from which several individuals (typically men) would eat. The bowl was found positioned upside-down amid a concentration of other whole and partial pottery vessels, grinding stones, charred seeds and wide-spread fire-hardened soil. The context is interpreted as a kitchen area destroyed by an incident of intense fire. Whole pot. Scale in cm. Site Makala Kataa. 4 July, 1989.
Rights:
Creative Commons Attribution--NonCommercial
Publisher:
University of Victoria Libraries
Provenance:
Makala Kataa, Station 6, Mound 5, 4W 4S, Level 7-8
Photo of a small pedestal-base pottery bowl. The rim of the bowl is broken away around the entire circumference of the bowl. The exterior surface is burnished and decorated with several triangular impressions (not visible on the surfaces in this photo). The bowl is consistent in shape and size with serving/eating bowls from which an individual (typically a woman) would eat. The bowl was found in association with several other pots and a laterite hearthstone in an area surrounded by oxidized fire-hardened sediment. The wider context of the excavation unit is interpreted as a kitchen area destroyed by an incident of intense fire. Scale in cm. Site Makala Kataa. 11 July, 1989.
Rights:
Creative Commons Attribution--NonCommercial
Publisher:
University of Victoria Libraries
Provenance:
Makala Kataa, Station 6, Mound 5, Unit 0W 4S, Level 5
Photo of a dark brown pottery jar rim, neck and body, with profile depicted (left). The rim of the jar is everted in profile. Below the neck, the body of the jar is decorated with a carved roulette rolled across the surface to create a herringbone design. The zone of carved roulette impression is bounded by a horizontal shallow groove. A curvilinear groove cuts across the roulette impression. The ceramic fabric contained both laterite and white grit, as well as finely crushed iron slag. INAA analysis ("NA B-143-8") assigned this jar to the "K1" group, with the implication that it was likely made on the east side of the Banda hills. Rim diameter: 22 cm at interior lip. Sherd represents an estimated 25% of the circumference of the jar. Scale in cm. Site B-143. 14 March, 2001.
Photo of a red-painted and mica-slipped bowl rim, with profile depicted (left). Toward the lip, multiple horizontal bands of grooving and dentate (comb) impression are overlaid by red paint. Below this is a zone with horizontal lines of wavy line impression and grooving overlaid by a mica slip. The lower zone is red-painted. The ceramic fabric includes finely crushed white grit which includes some quartz. An INAA sample ("A94-8") was assigned to the "L" group, indicating that the bowl was made from clays mined west of the Banda hills. Rim diameter: 14 cm at the interior lip. Sherd represents an estimated 15% of the bowl's circumference. Scale in cm. Site A-94. 21 February, 2001.
Rights:
Creative Commons Attribution--NonCommercial
Publisher:
University of Victoria Libraries
Provenance:
Site A-94, Mound 2, Unit 1, Level 6
Date:
2001-02-21
Location(s) Facet:
Site A-94
Subjects:
Wavy line impression; Dentate impression; Red paint; Mica slip; Bowl; Neutron Activation Analysis
Photo of the rim and shoulder of a large pottery bowl, with profile depicted (left). The bowl's exterior is decorated with a herringbone design, created by rolling a carved wooden roulette across its entire surface, except for a narrow band just below the bowl's lip. A single diagonal shallow groove was applied across the surface above the shoulder. An INAA sample (NA "A212-8") from this bowl was "unassigned" to a specific group of ceramic fabrics, lending no insight into where the bowl was made. Rim diameter: 20 cm at the interior lip. Sherd represents about 11% of the bowl's circumference. Scale in cm. Site A-212. 18 February, 2001.
Photo of an everted-rim jar. The round-based pot is decorated on its lower surface by maize cob impressions, created by rolling a kernel-less maize cob over the pot's surface. The top edge of the maize-cob-rouletted zone is marked by pendant grooves or channels. Small circular punctates mark the place where pendant grooved lines meet. A single grooved line offsets this decorated zone from an undecorated zone below the jar's neck. Whole pot. Scale in cm. Site A-9. 1 Feb. 2001.